Re: ��

Actan — �� 06, 2011 08:46

��: Actan

��: �� 06, 2011 08:46

��!

Re: ��

_Babushka_ — �� 04, 2011 14:25

��: _Babushka_

��: �� 04, 2011 14:25

REMOVAL
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
HINT:
At the time of installation, perform initialization (See INITIALIZATION ).
NOTE: Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.
2. REMOVE ROOF HEADLINING ASSEMBLY
Remove the roof headlining (see REMOVAL ).
NOTE: After removing the roof headlining, connect the cable to the negative (-) battery terminal and reconnect the map light connector.
3.REMOVE NO. 1 COOLER AIR DUCT
4.REMOVE SLIDING ROOF SIDE GARNISH
Using a screwdriver, detach the 2 claws and remove the garnishes.
HINT:
Tape the screwdriver tip before use.
5.REMOVE SLIDING ROOF GLASS SUB-ASSEMBLY
Remove the 4 nuts.
Pull the glass upward to remove it.

Fig. 18: Removing Sliding Roof Glass Sub-Assembly
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
6. REMOVE SLIDING ROOF DRIVE GEAR SUBASSEMBLY
NOTE: Remove the drive gear with the sliding roof fully closed.
Disconnect the connector.
Remove the 2 bolts and drive gear.

Fig. 19: Removing Drive Gear
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
Using a screwdriver, remove the cam plate cover.

Fig. 20: Removing Cam Plate Cover
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
HINT:
Tape the screwdriver tip before use.
Turn the drive gear to align the point marks as shown in the illustration.
NOTE: At the time of installation, refer to the following item. If the sliding roof position and drive gear fully closed position are not the same, the sliding roof will not operate normally.
Install the cam plate cover.

Fig. 21: Installing Cam Plate Cover
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.
7. REMOVE SLIDING ROOF HOUSING SUB-ASSEMBLY
Remove the 4 drain hoses from the housing.
Remove the room light wire harness.
Remove the 8 bolts, 2 nuts and sliding roof housing.

Fig. 22: Removing Sliding Roof Housing
Courtesy of TOYOTA MOTOR SALES, U.S.A., INC.

Re: ��

Actan — �� 04, 2011 13:56

��: Actan

��: �� 04, 2011 13:56

. ��, �� ... [/quote]

�� , � �� ?

Re: ��

�� — �� 04, 2011 09:59

��: ��

��: �� 04, 2011 09:59

�� , �� ...��, �� . ��, �� ...

Re: ��

VaNo52 — �� 04, 2011 09:35

��: VaNo52

��: �� 04, 2011 09:35

�� : �� , � ��. �� - ��, �� . �� . ��, �� . �� , �� , �� -�� , � �� , � �� .

Re: ��

�� — �� 04, 2011 08:53

��: ��

��: �� 04, 2011 08:53

�� ...

��

Actan — �� 03, 2011 16:47

��: Actan

��: �� 03, 2011 16:47

�� , � �� . �� (��, �� ) �� . ��, �� , �� , �� , � �� . �� , � �� , �� ?

���� ������ ������

Re: ����� ���� �������� �������� ���

Re: ����� ���� �������� �������� ���

Re: ����� ���� �������� �������� ���

Re: ����� ���� �������� �������� ���

Re: ����� ���� �������� �������� ���

Re: ����� ���� �������� �������� ���

����� ���� �������� �������� ���

��

Re: ��

Re: ��

Re: ��

Re: ��

Re: ��

Re: ��

��